Jump to main content
CALHYDRA Help
CALHYDRA Help
  • Start
  • User interface
  • Drinking water
  • Waste water
  • Heating
  • Appendix
  • Glossary
  • Support
Index
  1. Home
  2. Glossary

  3. Heating

  4. Minimum nominal volume of a diaphragm expansion vessel
  • Glossary

    • Drinking water

    • Waste water

    • Heating

      • 3-way fitting
      • System volume
      • Set pressure of a safety valve
      • Expansion volume
      • Design temperature of a section
      • Outer diameter of the insulation
      • Admixing circuit
      • Operating pressure
      • Reference storey
      • Bilfilar pipe routing
      • Bypass circuit
      • Insulation layer thickness
      • Insulating material
      • Ceiling thickness
      • Decentralised DHW heating
      • Density
      • Differential pressure regulators
      • Throttle valve
      • Pressure difference due to individual resistances
      • Pressure surge
      • Flow rate
      • Dynamic viscosity
      • Injection circuit
      • Setting value
      • Ultimate pressure
      • Individual resistor
      • Flow velocity
      • Flow direction
      • Flow path
      • Fluid temperature of a section
      • Floor structure
      • Storey width
      • Storey height
      • Trade
      • Simultaneity
      • House connection
      • Heating load
      • Hydraulic balancing (heating)
      • Hydraulic circuits
      • Cap valve
      • Kinematic viscosity
      • Kv value
      • Kvs value
      • Meandering pipework
      • Mass flow rate
      • Maximum setpoint on the temperature controller
      • Maximum filling pressure
      • Diaphragm expansion vessel
      • Measuring device
      • Minimum filling pressure of a diaphragm expansion vessel
      • Minimum nominal volume of a diaphragm expansion vessel
      • Network section
      • Top edge of finished floor
      • Product sequence
      • Percentage expansion of a fluid
      • Reynolds number
      • Pipe type
      • Outer pipe diameter
      • Outer pipe diameter of an insulated pipe
      • Pipe sequence
      • Pipe roughness
      • Pipe length
      • Pipe cross-sectional area
      • Pipe roughness
      • Pipe friction pressure gradient
      • Pipe friction coefficient
      • Return temperature
      • Return screw fitting
      • Return buffer volume
      • Resting pressure range of a diaphragm expansion vessel
      • Closing pressure differential of a safety valve
      • Safety temperature limiter
      • Safety valve
      • Specific heat capacity of water
      • Specific heat loss
      • Spreading
      • Flush valve
      • Static pressure
      • Control valve
      • Line regulating valve
      • Streamline
      • Section designation
      • Section number
      • Section type
      • Thermostatic valve
      • Transfer circuit
      • Ambient temperature
      • Deflection circuit
      • Vaporisation pressure
      • Valve
      • Valve authority
      • Connecting component
      • Consumer
      • Viscosity
      • Volume flow controller
      • Back pressure at the diaphragm expansion vessel
      • Flow temperature
      • Priority switching
      • Heat transfer coefficient of an insulated pipework
      • Heat generator
      • Thermal conductivity
      • Heat loss
      • Wall thickness (pipe)
      • Water seal of a diaphragm expansion vessel
      • Material
      • Drag coefficient

Minimum nominal volume of a diaphragm expansion vessel

The minimum nominal volume of a diaphragm expansion vessel is the smallest nominal volume of a diaphragm expansion vessel that is still permissible. The minimum nominal volume depends on the expansion volume V e, the water supply VV of the diaphragm expansion vessel, the final pressure Ve and the inlet pressure p0.

Symbol or abbreviation:

VN,min

Usual unit:

l

Equation:
See also
  • Diaphragm expansion vessel
www.dendrit.com | Impressum | AGB | Datenschutz