Home
Appendix
Dialogues and additional information
Drainage areas
The Drainage areas window in the Drainage section is divided into two tabs.
Open spaces
Open areas overview
The tabular overview in the Drainage areas window on the Open areas tab displays information on all open areas created in the drawing.
Column J
Column J in the Drainage areas window on the Open areas tab shows the optionally specified gradient in cm/m.

Appendix
- Dialogues and additional information
  - Wastewater lifting unit
  - Design options (waste water)
    Drawing-specific settings relating to your calculation are set in the Design options dialogue.
  - Design options (heating)
    Drawing-specific settings relating to your calculation are set in the Design options dialogue.
  - Design options (drinking water)
    Drawing-specific settings relating to your calculation are set in the Design options dialogue.
  - Construction stages
    You can divide a drawing into construction stages so that you can later create a material extract according to construction stages.
  - Component properties
    In the Edit and Calculate work perspective, your selection in the drawing is highlighted in colour. Section properties and component properties can be displayed and edited differently from the global project settings.
  - Component filter
    The component filter allows you to quickly filter the selected components in the drawing.
  - Drainage areas
    The Drainage areas window in the Drainage section is divided into two tabs.
    - Roof areas
    - Open spaces
      - Add open areas
        Use Add area to create a new open area in the tabular overview of the Drainage areas window on the Open areas tab.
      - Delete open spaces
        Delete removes selected open spaces from the table overview. In addition, the corresponding open space polygons in the floor plan drawing are removed from the drawing.
      - Place drains
        The Place drains function provides you with intelligent placement routines for open spaces in floor plan drawings. Customisable default settings including plausibility checks of the value entries are made, taking individual technical specifications into account.
      - Hatching open spaces
        Provide the open spaces in a floor plan drawing with a grey hatching for an overview.
      - Open areas overview
        The tabular overview in the Drainage areas window on the Open areas tab displays information on all open areas created in the drawing.
        Designation column
        The Designation column in the Drainage areas window on the Open areas tab displays the unique identifier of the open area.
        Area column
        The Area column in the Drainage areas window on the Open areas tab shows the total area of the individual open areas.
        Drainage coefficient column
        The Runoff coefficient column in the Drainage areas window on the Open areas tab shows the peak runoff coefficient C_S of the roof area.
        Target discharge column
        The QSoll column in the Drainage areas window on the Open areas tab shows the calculated target discharge in l/s.
        Floodable without damage column
        The Floodable without damage column in the Drainage areas window on the Open areas tab allows you to activate the open area as a floodable without damage area. As soon as an area is activated as harmlessly floodable, the flooding height is calculated. A distinction is made here between a flat surface and a sloping surface.
        Column J
        Column J in the Drainage areas window on the Open areas tab shows the optionally specified gradient in cm/m.
        Backwater column
        The Lrück column in the Drainage areas window on the Open areas tab shows the optionally specified length of the backwater edge in metres.
        Backflow column
        The Vrück column in the Drainage areas window on the Open areas tab shows the calculated backwater volume in m³.
        Column hü
        The hü column in the Drainage areas window on the Open areas tab shows the calculated flooding height h_ü in cm.
  - Find function
    CALHYDRA has a parameterised search function that supports you when searching for drawn sections and components in the drawing and when selecting products.
  - Hydraulics report
    With the preview of the calculation output, CALHYDRA supports you in customising the calculation output.
  - Mass extract
    With the preview of the mass statement, CALHYDRA supports you in customising the printout of the masses.
  - Material editor
    With the material editor, CALHYDRA supports you with convenient and fast determination of your dimensions.
  - Diaphragm expansion vessel
  - Options Wizard (waste water)
    The options wizard guides you through the settings for the design.
  - Options assistant (heating)
    The options wizard guides you through the settings for the design.
  - Options Wizard (drinking water)
    The options wizard guides you through the settings for the design.
  - Project data
    The Project data dialogue contains project information for the current project, for example for the project cover sheet or to determine the rainfall donations.
  - Product sequence or product selection
    In the Product sequence or Product selection dialogue, select the product sequence or a product for components.
  - Project data
    The Project data dialogue contains project information for the current project, for example for the project cover sheet or to determine the rainfall donations.
  - Simulation
    The simulation is divided into a circulation simulation for hot and cold water and a simulation of a cold water hygiene system.
  - Section properties
    In the Edit and Calculate work perspective, your selection in the drawing is highlighted in colour. Section properties and component properties can be displayed and edited differently from the global project settings.
  - Insert drawing reference
    The Insert drawing reference function guides you through the settings for inserting a drawing reference.
  - Water softening system

Column J

Column J in the Drainage areas window on the Open areas tab shows the optionally specified gradient in cm/m.

Enter the desired slope of the open areas in cm/m in the input fields in column J.

Note:

If you have not entered a gradient, you cannot specify a backwater edge (L_Rück) length.